Če prav razumem, lahko s kosom žice in eno žarnico aktiviraš opozorilno lučko za motorno elektroniko. Valjo je zadevo povzel na team-audi.si. Zadeva najbrž deluje tudi na navadni osemdesetki (in tudi stotki).
Glede na enostavnost posega, se bom ob prvi priložnosti lotil zadeve.
Na http://www.s2central.net/inst_clust_mil.html so naslednja navodila:
Instrument Cluster - MIL Circuit
Tools Required :
Cross-headed screwdriver
Long thin 'terminal' screwdriver
Miniature screwdriver or probe
Soldering Iron, Wire strippers, cutters & Pliers
8mm socket & driver
An optional multimeter can be handy !
Time Required :
About 1-2 hours, depending on electrical skills
Parts Required :
2W inst bulb (green) 893 919 040A
1m length of cable (0.5mm2)
Splice or Spade connectors - your choice
Small tie-wraps and/or insulating tape
WARNING !
It is not absolutely necessary to disconnect the battery before doing this job as all the relevant connectors have female plugs, but it is better to be safe than sorry with all electrical tasks and the negative lead at the battery should be disconnected if you are in any doubt about proceeding further.
What is the MIL circuit ?
It is a little known fact that Audi 80 & Coupes exported to the USA had to comply with Californian legislation which dictated that the driver had to be informed of certain (emission related) engine fault conditions by means of a warning lamp. This is known as the Malfunction Indicator Lamp - or MIL for short.
The MIL circuit is not fully wired up on Audi 80s & Coupes that were not destined for California, but I have discovered how to activate this function on the S2 after many hours of 'reverse engineering' the instrument cluster and probing round the wiring loom.
Why should I be interested in a MIL circuit ?
The MIL circuit is connected to the blue coloured OBD plug that is fitted to the car which is ultimately controlled by the ECU. This same blue (MIL) plug can be used to retrieve fault / blink codes from the ECU.
All of this means that, by adding a MIL circuit onto the S2 cluster, there would be no need for messing about with LEDs and test lamps to pull fault codes . But more importantly, the MIL circuit will inform the S2 driver of many active fault conditions that the ECU can detect whilst the engine is running. It does this by illuminating the MIL until the fault clears. Any faults are stored in the ECU and can then be blinked out on the MIL as soon as it is convenient to do so.
The cost of adding the MIL circuit is very low indeed - needing only a single instrument bulb, a short section of narrow guage cable and a connector or two.
NOTE - The MIL circuitry does not flash out the blink codes until the blink code sequence is activated as normal. This prevents driver distraction.
How do I wire up the MIL circuit in my S2 ?
The following gives a fairly detailed description, in three parts, as to how the MIL circuit can be activated on the S2. I have proved it out on my 94 ABY but it has also been proven out on a 3B. It is very simple electrics requiring a single wire be added to the loom and a new bulb be added to the instrument cluster in an unused location. Some soldering skills are needed along with basic electrical tools.
Some links below are to related pages on this site, others link to decent sized JPG photos. There are also some embedded images in this page where necessary.
PART 1 - Preparing the Loom
1. Firstly, remove the instrument cluster as described here , and set it to one side in a safe place to prevent damage until Part 2 below.
2. Locate the yellow coloured 26-pin connector (T26) behind the instrument cluster and snip off the tie-wrap which secures the wiring to the connector shell. Be extra careful to only snip the tie wrap !
3. Using a miniature screwdriver (or a fine tipped probe), tease apart the hood from this yellow connector and slide it off to expose the electrical wiring and connection pins as shown in this photo .
4. Locate pin 24 (twenty four) on the yellow connector. The connector moulding is numbered to assist with this task - it is two from the end as shown in this photo . Pin 24 is an unused connection point, so there should be no wire attached to this pin - until these tasks are complete. If your car is an MY95 vehicle, fitted with the factory immobiliser, then this connection point must NOT be used. Click here for more details and an alternate lamp location.
5. Again using the miniature screwdriver (or probe), GENTLY disengage the locking tab for pin 24 and remove it from the yellow connector, as shown here .
6. A special crimping tool is specified for these pins, which none of us will likely have access to, so I recommend that a soldering iron is used to connect a 1m length of multicore (0.5mm 2 diameter) cable onto this pin. If you choose cable which is too thick then this will be difficult and the pin may not fit back into the connector.
7. Carefully return the locking tab of the connector pin (with new wire attached) to its original position and slide it back into position 24 (twenty four) of the yellow cluster connector. It will lock itself into place.
8. Reassemble the yellow connector hood, taking care not to snag any cables and attach a new tie wrap onto the connector hood when finished. With this new length of wire dangling from the yellow cluster connector the fiddliest task is complete.
PART 2 - Preparing the Cluster
9. Now the attention turns to the instrument cluster... With the cluster lying face down on a soft surface, remove the sticky cover for the unused 'CAT' warning lamp as shown in this photo and fit the green 2W lamp in this location. At this point it is worth noting that the early cars have an unused yellow warning symbol that resembles a steering wheel in deference to the 'CAT' legend on later cars. Dunno why - but I'm 100% sure that this is the correct lamp location for the MIL bulb on Californian cars. This link lists the different warning lamp legends applicable to the S2. Please note that if you have an MY95 S2 (S chassis) with the factory fitted immobiliser - you will have to work with the unised lamp location above the 'CAT' lamp. More details here.
10. Reconnect all of the electrical plugs back into the instrument cluster as normal.
11. At this point, you may wish to test the newly installed cable and CAT lamp. Do this by turning on the ignition and then touching the other end of the new wire to the chassis (0V). The red CAT lamp will only be lit whilst this circuit to 0V/earth is closed.
12. Temporarily loop or tuck the new section of wire in behind the instrument cluster which can then be refitted as normal.
PART 3 - Completing the MIL Circuit
13. Now working in the driver side footwell, use an 8mm socket to remove the four bolts which secure the parcel shelf to the dashboard. Three bolts are on the top edge, and the fourth is down near the bonnet release.
14. Slide the parcel tray carefully out of the plastic clip at the pedals. If your car has diagnostic plugs in the drivers parcel shelf (early 3B only) then you may wish to unclip them, so that the tray can be moved out of the way for the next tasks. Try not to panic when you see the mad rampant mess of spaghetti cabling which is lurking under the dash. Fortunately, the access you need is very easy.
15. Locate the new loop of cable which connects to the yellow cluster plug from Part 2. Unloop it, then tie-wrap and/or tape it along the existing loom from the cluster such that it makes a sensible route to the black 5-pin connector (known as T5) shown in this photo . This is where it will connect to the 'blink output' driver from the ECU. Leave enough slack cable to work with for the new connection point.
16. Looking at the T5 connector, you will see a gray/brown (gr/br) coloured wire on the pedal side of the connector which is unterminated. On the ABY engine this corresponds to pin 4 (four) on the T5 plug, but it is pin 3 (three) on the 3B engine (thanks to Steve Henson for confirming that). This is the wire needed to drive the MIL function. As a double-check, you can perform a continuity test with a multimeter from this wire to the BLUE diagnostic plug on your car. The reading should be a short circuit (0 Ω) confirming that you have located the correct wire !
17. Trim and connect the new wire from the cluster to this gray/brown wire on T5. An ideal connection would be with a crimped pin that inserts into the empty receptacle of T5 but such connector pins and crimp tools are very hard to find. Other ways to make the connection are with insulated male & female spade terminals or with a 'scotchlok' style connector. The latter has the advantage of not needing to cut into the gray/brown wire and fiddle about with wire strippers and crimpers etc. Either way, make a secure connection and ensure all the wiring is neatly and safely taped or tied into the factory loom.
Now turn on the ignition and look with awe and amazement at the newly illuminated 'CAT' lamp which serves as a wonderful Malfunction Indicator Lamp (MIL).
MIL ON
Some brief notes on MIL operation -
* When the engine is started the CAT lamp will extinguish.
* It will only illuminate with the engine running when there is an active fault detected by the ECU.
* Additionally, the MIL circuit can be used to view blink codes whenever required. Simply follow the directions in this page but forget fiddling with the LED or test lamp at the blue connector.
* Finally, when the ECU is communicating with VAG-COM (or VAG1551) in basic settings mode the MIL circuit is activated. This will undoubtably raise an eyebrow at your local VAG dealership